1 & 220vAC 1.5kw ER11 Air Cooled Spindle Motor 65mm 4 bearings
1 & 220v 1.5kw VFD / Inverter
Size: 65 x 204mm ( Body diameter:65mm; Length:204mm)
Speed Ways: Through 3-phase output inverter and adjust the inverter frequency to change the spindle speed.
Cooling: Air cooling
Power Interface: Optional H17-4 pins waterproof air plug. The air plug marked "1 ","2"," 3"," 4", "1 ","2 ","3" were connected to inverter (U, V, W), 4 connected inverter ground. (Pay attention! our spindle "4" connecting to GND,promised personal safety!!)
Power: 1.5kw (1HP=0.735kw)
Voltage: 220vAC (If you need 110v/380v spindle ,please leave message to us,thank you)
Runout Off: 0.01mm
Bearing Type: 2X7002C P4 DT and 2X7002C P4 DT
Full sealed angular contact bearings
Clip Knifediameter: 7mm,6.35mm,6mm,5mm,4mm,3.175mm,3mm,2mm,1mm
Air Cooling ER11 collet chunk
Main Application: Engrave for wood,bamboo,normal PCB,PVC,PMMA,plastic,duotone board(ABS)and etc nonmetal, also can engrave on gold,silver,copper, aluminium,Pb etc soft metal surface working. (Please pay more attention, this is wood working spindle, only can used for wood working and aluminum working,please don\'t use it for steel. If you need steel working,please check the metal spindle,thank you!)
Preparations before use
Spindle working environment temperature is usually -10 ~ 40 .
Before installing the first electric spindle axis head turned by hand, should feel flexible, non-blocking phenomenon.
Spindle in the preservation and transportation, high-speed grease inside the bearing state will change, customers should be running at low speed for 30 minutes. 3000 rpm and then follow the poor increase, run 20 minutes each. Spindle and the inverter should be working together. The inverter\'s specifications and parameter settings need match spindles parameter.
Connect the inverter spindle, three-phase inverter power cord should be soldered in the plug 1 (U), 2 (V), 3 (W) feet, 4 feet for the ground. After the power is turned on, to observe whether the spindle rotation axis indicates the direction consistent. If inconsistency should be immediately shut down, replace the inverter and spindle connected two wires of three-phase power supply.
During normal operation, air-cooled spindle often encounter the phenomenon of heat, always check whether the air-cooled spindle housing and duct clogging dust.If clogging dust, to promptly clean up. If you do not clean up, it is easily to make the spindle burned.
Every day before using the spindle must be running at low speed for 15-20 minutes. Clamping the cutters to spindle, collet nuts ,collets,cutters must be clean enough. Shank inserted into the collet must be greater than 15mm.
Care and maintenance:
Spindle frequency power supply connected rated voltage, frequency should be consistent with the technical parameters of the electro-spindle, spindle speed can be adjusted to change the frequency, and voltage is proportional to the change.
Spindle being not used, spindle appearance should be oiled. Plus the shaft protection device, put in a dry place.
To replace the spindle bearings, certain professional and technical personnel should be replaced. Supporting special tools, bearings should be replaced fully cleaned without removing the stator coils.
Bearing is P4 grade,2×7002C P4 DT &2×7002C P4 DT, increase spindle life.
High speed,high torque,low noise,low price.
High precision,runout off less than 0.01mm.Coaxial degree less than 0.0025mm
Shipment within four days,there is no fake tracking number,make sure that you receive time.
We are the spindle manufacturer ,we offer only best quality and best price to you.
Tech parameters: Inverter Type:220v 1.5kw
Input Voltage: 220V(+/-15%)
Output Voltage: 220vAC
Input Frequency : 48-63 Hz
Output Frequency: 0-400 Hz
Input Phase: 1 or 3 phase
Output Phase: 3 phase
Warranty: 1 year from the date you purchased
PID control; advanced calculus PID closed-loop arithmetic, quick responding speed and high suitability;
Easy PLC function can realize 16 legs of speed and inverter control function;
RS485 communication port, adopting standard international MODBUS main circuit control;
With extremely strong anti-jamming capability
Low output ratting torque0.5HZ-150%, low speed running ability;
Carrier adjustable by 16KHZ, completely soundless working environment;
Broad voltage working area, normal running in 304V-456V;
Auto voltage regulation (AVR) technique, for ensuring the inverter load capability;
Various control technique by both synchronization and non-synchronization, dynamically realize fast starting without changing brakes;
With perfect error protection and short circuit starting protection capability;
Control mode is SPWM,it is very easy to use and convenient
Protection functions are very strong,
Fin over-heat protection,
Restart after instant stop,stall protection.
Customer product display
Spindle engraving products show
Spindle production process
Spindle from the production - assembly - test, and finally the perfect packaging . We will 100% guarantee security to the hands of the guests.
Our products are sold worldwide.
If you need many items in the same time, please contact us in advance to confirm shipping cost.
We accept paypal credit, bank transfer, western union etc.
Payment must be made within 7days calendar days of the auction end time.
Problem and Feedback:
PLEASE DON\'T leave any negative feedback before you contact us.
We are honest and helpful supplier , we will try our best to solve problems with you.
Your satisfaction is very important for our store, so please contact us before you want to leave a negative feedback.
- Brand Name: G-PENNY MACHINE
- Drive: Motor
- Operating Speed: 0-24000rpm
- Model Number: 1.5kw ER11 65mm Air cooled spindle motor
- Maximum Torque: 0.46Nm
- Application: Milling
- Size: 65x204mm ( 65mm diameter )
- Voltage: 220v
- Current: 6 A
- Power: 1.5kw
- Cooling: Air Cooled
- Bearing type: 2X7002C P4 DT and 2X7002C P4
- Collet: ER11
- Frequency: 400Hz
- Collet Range: 1-7mm (Including 1/8,1/4 )
- Inverter Type: 220v 1.5kw 400Hz